300 Win Mag once-fired case trimming
Moderators: carlson1, Charles L. Cotton
-
Topic author - Senior Member
- Posts in topic: 3
- Posts: 9655
- Joined: Tue Aug 12, 2008 9:22 pm
- Location: Allen, Texas
300 Win Mag once-fired case trimming
300 Win Mag Spec asks for Case length not exceeding 2.620"
However, my once fired brass was cleaned and primed and I assume that no need for trimming. However, when I checked case length, I was seeing 2.628"-2.636" That is 0.008" to 0.016" over.
Is that okay or should I de-prime and size then prime again?
However, my once fired brass was cleaned and primed and I assume that no need for trimming. However, when I checked case length, I was seeing 2.628"-2.636" That is 0.008" to 0.016" over.
Is that okay or should I de-prime and size then prime again?
Beiruty,
United we stand, dispersed we falter
2014: NRA Endowment lifetime member
United we stand, dispersed we falter
2014: NRA Endowment lifetime member
-
- Senior Member
- Posts in topic: 4
- Posts: 631
- Joined: Fri Nov 20, 2009 1:43 pm
- Location: Coppell
Re: 300 Win Mag once-fired case trimming
Unless you are trying to achieve "Match Grade" I would not worry about it.
If shooting out of a bolt gun, the case will fire form to the chamber. Most semi-auto chamber are a little looser by design anyway.
Just my opinion.
If shooting out of a bolt gun, the case will fire form to the chamber. Most semi-auto chamber are a little looser by design anyway.
Just my opinion.
Guns are like parachutes, if your ever in a situation that you need one and you dont have one, you'll probably never need one again.
-
Topic author - Senior Member
- Posts in topic: 3
- Posts: 9655
- Joined: Tue Aug 12, 2008 9:22 pm
- Location: Allen, Texas
Re: 300 Win Mag once-fired case trimming
I am trying to load:
Re-used case: Hurter's Select Hunting rds, once fired.
Primer: Win LR Mag
Powder: Alliant Power Pro 4000-MR (Similar to RL-22?) 70 grs.
Bullet: Hornady .30 Cal 208 gr A-max.
Rifle: Steyr SSG-04 with factory certificate of 0.6 MOA
Purpose: to get 5 rds all touching at 100yrds.
Re-used case: Hurter's Select Hunting rds, once fired.
Primer: Win LR Mag
Powder: Alliant Power Pro 4000-MR (Similar to RL-22?) 70 grs.
Bullet: Hornady .30 Cal 208 gr A-max.
Rifle: Steyr SSG-04 with factory certificate of 0.6 MOA
Purpose: to get 5 rds all touching at 100yrds.
Last edited by Beiruty on Fri May 30, 2014 8:28 pm, edited 1 time in total.
Beiruty,
United we stand, dispersed we falter
2014: NRA Endowment lifetime member
United we stand, dispersed we falter
2014: NRA Endowment lifetime member
-
- Senior Member
- Posts in topic: 4
- Posts: 631
- Joined: Fri Nov 20, 2009 1:43 pm
- Location: Coppell
Re: 300 Win Mag once-fired case trimming
This is a bolt gun?
Was the brass you are using shot from your chamber? If not, I would fire a few rounds through it to fire form the brass. Then Neck-Size the brass and trim. Fire forming the brass shapes it to the exact form of your chamber then the brass will have no room to move in the chamber. It will headspace perfectly.
Are you using bench rest quality primers?
Seat the projectile as close to the rifling as you can and weigh your powder charges very closely.
Then you can go for 0.6 MOA.
Was the brass you are using shot from your chamber? If not, I would fire a few rounds through it to fire form the brass. Then Neck-Size the brass and trim. Fire forming the brass shapes it to the exact form of your chamber then the brass will have no room to move in the chamber. It will headspace perfectly.
Are you using bench rest quality primers?
Seat the projectile as close to the rifling as you can and weigh your powder charges very closely.
Then you can go for 0.6 MOA.
Guns are like parachutes, if your ever in a situation that you need one and you dont have one, you'll probably never need one again.
-
- Senior Member
- Posts in topic: 4
- Posts: 631
- Joined: Fri Nov 20, 2009 1:43 pm
- Location: Coppell
Re: 300 Win Mag once-fired case trimming
Since I started fire forming brass for my Rem 700, I'm hitting a 10" plate at 400 yards every shot. Not quite 0.6 MOA, but it works for me.
Guns are like parachutes, if your ever in a situation that you need one and you dont have one, you'll probably never need one again.
-
Topic author - Senior Member
- Posts in topic: 3
- Posts: 9655
- Joined: Tue Aug 12, 2008 9:22 pm
- Location: Allen, Texas
Re: 300 Win Mag once-fired case trimming
Yes, it is a bolt action.
Here is the steps I am doing right now.
1) Lube the case with LEE lube
2) De-prime and size (factory die at this time, I may switch to neck-size)
3) Sonic clean the brass for like 25-30 min
4) Trim the case to factory spec
5) Weigh the powder with Hornady auto-dispenser
6) load the charge using a funnel.
7) Seat the bullet to 3.340" (factory spec) or 3.350" for deeper seated bullet into the chamber
9) Lee Factory crimp (optional)
Go shoot group of 5rds.
First 10 rds at 3.340" OAL.
First 10 rds at 3.350" OAL.
Here is the steps I am doing right now.
1) Lube the case with LEE lube
2) De-prime and size (factory die at this time, I may switch to neck-size)
3) Sonic clean the brass for like 25-30 min
4) Trim the case to factory spec
5) Weigh the powder with Hornady auto-dispenser
6) load the charge using a funnel.
7) Seat the bullet to 3.340" (factory spec) or 3.350" for deeper seated bullet into the chamber
9) Lee Factory crimp (optional)
Go shoot group of 5rds.
First 10 rds at 3.340" OAL.
First 10 rds at 3.350" OAL.
Last edited by Beiruty on Fri May 30, 2014 8:37 pm, edited 2 times in total.
Beiruty,
United we stand, dispersed we falter
2014: NRA Endowment lifetime member
United we stand, dispersed we falter
2014: NRA Endowment lifetime member
-
- Senior Member
- Posts in topic: 1
- Posts: 3058
- Joined: Sun Jan 17, 2010 11:19 am
- Location: Converse, TX
Re: 300 Win Mag once-fired case trimming
THIS!!!!ddstuder wrote:This is a bolt gun?
Was the brass you are using shot from your chamber? If not, I would fire a few rounds through it to fire form the brass. Then Neck-Size the brass and trim. Fire forming the brass shapes it to the exact form of your chamber then the brass will have no room to move in the chamber. It will headspace perfectly.
The books can only tell you what the SAMMI spec is. If you want accurate handloads, you MUST "listen" to your rifle. It will tell you the right case length (with once-fired casings from it) as well as proper cartridge length to the lands.
Read the article by Brian Litz on cartridge length here (http://www.bergerbullets.com/effects-of ... to-part-1/" onclick="window.open(this.href);return false;). You should fine-tune your jump distance to what works best, and RECORD EVERYTHING.
Have fun!
I don't fear guns; I fear voters and politicians that fear guns.
-
- Senior Member
- Posts in topic: 4
- Posts: 631
- Joined: Fri Nov 20, 2009 1:43 pm
- Location: Coppell
Re: 300 Win Mag once-fired case trimming
Load a few and shoot through the rifle. Then switch to neck size directly after. This will require a neck sizeing die. Different than what you have. After a couple firings don't for get to anneal the brass. It will make it last longer. 300 mag is not a chunk of brass people leave on the ground. Take care of your brass and customize it to your rifle.Beiruty wrote:Yes, it is a bolt action.
Here is the steps I am doing right now.
1) Lube the case with LEE lube
2) De-prime and size (factory die at this time, I may switch to neck-size)
3) Sonic clean the brass for like 25-30 min
4) Trim the case to factory spec
5) Weigh the powder with Hornady auto-dispenser
6) load the charge using a funnel.
7) Seat the bullet to 3.340" (factory spec) or 3.350" for deeper seated bullet into the chamber
9) Lee Factory crimp (optional)
Go shoot group of 5rds.
First 10 rds at 3.340" OAL.
First 10 rds at 3.350" OAL.
You'll be glad you did.
Guns are like parachutes, if your ever in a situation that you need one and you dont have one, you'll probably never need one again.
Re: 300 Win Mag once-fired case trimming
I actually have 62 pcs of once fired if your interested
Houston, Tx.
DPS Received - Jan. 26th
Received Pin# - Feb. 25th
IN HAND!!!!!! June 9th
DPS Received - Jan. 26th
Received Pin# - Feb. 25th
IN HAND!!!!!! June 9th