S&W S6hield Front Sight Removal

Holsters, sights, magazines, etc.

Moderators: Keith B, carlson1

Post Reply

Topic author
BSHII
Junior Member
Posts in topic: 1
Posts: 42
Joined: Thu May 17, 2018 3:33 pm

S&W S6hield Front Sight Removal

#1

Post by BSHII » Wed Nov 28, 2018 3:56 pm

After a few frustrating trips to the range with my S&W M&P Shield 9mm, I realized that the front sight is badly misaligned, to the point where it's grouping 6+ inches to the left at 7 yards. After Googling it, I see that others have reported exactly the same issue.

The manual states that the front sight can be adjusted by drifting it with a brass punch. I knocked it around pretty good with a brass punch, but it wouldn't budge.

I then decide to replace the sights, because I don't shoot 3-dot sights well anyway. I buy a sight pusher and am able to remove and replace the rear sight. It put up a struggle, but ultimately it wasn't too difficult.

The front sight, however, would not budge, and actually broke the sight pusher. I then resort to pounding the hell out of it with brass punches, bending several of them. I then use a steel punch with PVC tape on it and pound on that as hard as I dare for fear of marring the finish, and that doesn't work either. I tried freezing the slide as one internet poster suggested, but that, rather predictably, did not work.

I'm left with a somewhat deformed, brass-marked and misaligned white dot front sight, in front of my nice, properly-centered Wilson Combat Vickers Elite rear.

Apparently I'm not the first to experience the problem of a stubborn front sight either. Does anyone have any ideas? If someone knows a gunsmith in the Houston area who could remove it for a reasonable price (I can install my own replacement), I'd appreciate that as well.

User avatar

bblhd672
Senior Member
Posts in topic: 1
Posts: 4811
Joined: Mon Jun 06, 2016 10:43 am
Location: TX

Re: S&W S6hield Front Sight Removal

#2

Post by bblhd672 » Wed Nov 28, 2018 4:09 pm

M&P pistol series are tapered and the sights go out left-to-right and back in right-to-left. Is it possible you were trying to drive the sight out right to left?
The left lies about everything. Truth is a liberal value, and truth is a conservative value, but it has never been a left-wing value. People on the left say whatever advances their immediate agenda. Power is their moral lodestar; therefore, truth is always subservient to it. - Dennis Prager

User avatar

Scott B.
Senior Member
Posts in topic: 1
Posts: 1285
Joined: Tue Aug 05, 2014 11:46 am
Location: Harris County

Re: S&W S6hield Front Sight Removal

#3

Post by Scott B. » Wed Nov 28, 2018 4:19 pm

BSHII wrote:
Wed Nov 28, 2018 3:56 pm
After a few frustrating trips to the range with my S&W M&P Shield 9mm, I realized that the front sight is badly misaligned, to the point where it's grouping 6+ inches to the left at 7 yards. After Googling it, I see that others have reported exactly the same issue.

The manual states that the front sight can be adjusted by drifting it with a brass punch. I knocked it around pretty good with a brass punch, but it wouldn't budge.

I then decide to replace the sights, because I don't shoot 3-dot sights well anyway. I buy a sight pusher and am able to remove and replace the rear sight. It put up a struggle, but ultimately it wasn't too difficult.

The front sight, however, would not budge, and actually broke the sight pusher. I then resort to pounding the hell out of it with brass punches, bending several of them. I then use a steel punch with PVC tape on it and pound on that as hard as I dare for fear of marring the finish, and that doesn't work either. I tried freezing the slide as one internet poster suggested, but that, rather predictably, did not work.

I'm left with a somewhat deformed, brass-marked and misaligned white dot front sight, in front of my nice, properly-centered Wilson Combat Vickers Elite rear.

Apparently I'm not the first to experience the problem of a stubborn front sight either. Does anyone have any ideas? If someone knows a gunsmith in the Houston area who could remove it for a reasonable price (I can install my own replacement), I'd appreciate that as well.

Check your PMs.
LTC / SSC Instructor. NRA - Instructor, CRSO, Life Member.
Sig pistol/rifle & Glock armorer | FFL 07/02 SOT

Post Reply

Return to “Holsters & Accessories”