Hornady 45 cal 230gr FMJ-RN
Bullseye 5.2, 5.4 & 5.6gr
Everything seemed OK at 5.2gr
All rounds OK at 5.4gr, except the slide locked-back with a single round left in the magazine.
At 5.6gr I had the slide lock-back several times during the 2 magazines of rounds. Also, on the last round I had a stove-pipe (not sticking up, but jammed between the breach and the chamber).
Haven't heard of premature lock-back being a sign of overpressure, but thought I'd ask the experts!
In total I fired 76 rounds today, and this was at the end, so the gun was not particularly clean at this point. But I would think my Kimber Ultra CDP II would handle more than that without needing to be cleaned.
Maybe the extra recoil causing the slide-stop to bounce?
Any ideas?
1911 premature slide lock back
Moderators: carlson1, Charles L. Cotton
-
Topic author - Senior Member
- Posts in topic: 2
- Posts: 6267
- Joined: Wed Oct 28, 2009 7:14 am
- Location: Flint, TX
1911 premature slide lock back
Range Rule: "The front gate lock is not an acceptable target."
Never Forget.
Never Forget.
Re: 1911 premature slide lock back
Check your slide stop for signs of brass. The nose of the round can bump on the stop and engage it.
-
- Senior Member
- Posts in topic: 1
- Posts: 6745
- Joined: Sat Jun 19, 2010 11:16 am
- Location: Hunt County
Re: 1911 premature slide lock back
Premature slide lock is a known issue with Kimbers. Give them a call & they will send you a new slide stop with a slightly modified profile.
DocV is right. It's caused by the the nose of the top round hitting the slide stop.
DocV is right. It's caused by the the nose of the top round hitting the slide stop.
Facts are stubborn things; and whatever may be our wishes, our inclinations, or the dictates of our passions, they cannot alter the state of facts and evidence. - John Adams
-
- Moderator
- Posts in topic: 1
- Posts: 6185
- Joined: Tue May 27, 2008 9:59 pm
- Location: DFW Metro
Re: 1911 premature slide lock back
Check your grip also.
It's possible to accidentally put pressure on the slide stop during recoil.
This is usually more of a problem with small gun / big hand combinations, but it's something that should be considered if you're not seeing brass marks on the slide stop. Use of an aftermarket extended slide stop can also contribute to this issue.
It's possible to accidentally put pressure on the slide stop during recoil.
This is usually more of a problem with small gun / big hand combinations, but it's something that should be considered if you're not seeing brass marks on the slide stop. Use of an aftermarket extended slide stop can also contribute to this issue.
Excaliber
"An unarmed man can only flee from evil, and evil is not overcome by fleeing from it." - Jeff Cooper
I am not a lawyer. Nothing in any of my posts should be construed as legal or professional advice.
"An unarmed man can only flee from evil, and evil is not overcome by fleeing from it." - Jeff Cooper
I am not a lawyer. Nothing in any of my posts should be construed as legal or professional advice.
-
Topic author - Senior Member
- Posts in topic: 2
- Posts: 6267
- Joined: Wed Oct 28, 2009 7:14 am
- Location: Flint, TX
Re: 1911 premature slide lock back
Are you talking about copper from the bullet? The brass shell is about 1/4" behind the stop.
Range Rule: "The front gate lock is not an acceptable target."
Never Forget.
Never Forget.
Re: 1911 premature slide lock back
Yup. The rounds can move forward in the magazine when firing but I would be concerned if the nose of the shell was 1/4" behind the stop. Here is a photo of a 1911's slide stop in a magazine that is being inserted:sjfcontrol wrote:Are you talking about copper from the bullet? The brass shell is about 1/4" behind the stop.
In the picture, the magazine is not yet seated. Here is a picture with the magazine fully seated.
As you can tell the rounds in this picture are jacketed hollow points.
Here is a FMJ brass jacketed Montana Gold in a magazine that is not yet seated:
If round moves slightly forward in the magazine it can impact the slide stop. If that is happening you might find marks on the slide stop lug. If so, you can try lightly filing your slide stop to profile it away from the nose of the bullet or just get a replacement slide stop from Kimber. If you reload, you can see what happens if you shoot SWCs.