Ruger new model single six part identification
Moderator: carlson1
Ruger new model single six part identification
This is a ruger new model single six with both 22lr and 22 wmr cylinders.
Can anybody Identify the small pin and what part of the gun it may go to.
Thank you.
Can anybody Identify the small pin and what part of the gun it may go to.
Thank you.
Re: Ruger new model single six part identification
I don’t know if this will help my friend. Good luck. I hate it when I have parts left over.
Re: Ruger new model single six part identification
https://www.gunpartscorp.com/gun-manufa ... e-6?page=4
8 or 31
Cylinder latch spring plunger
Pawl spring plunger
8 or 31
Cylinder latch spring plunger
Pawl spring plunger
NRA Life Member
Re: Ruger new model single six part identification
31 should be stepped to hold the spring. Don't know 8 could be possible.BHill wrote: Thu Sep 12, 2019 10:08 pm https://www.gunpartscorp.com/gun-manufa ... e-6?page=4
8 or 31
Cylinder latch spring plunger
Pawl spring plunger
Re: Ruger new model single six part identification
Trust me, I've no doubt taken enugh stuff apart in my life to be able to put it back together.carlson1 wrote: Thu Sep 12, 2019 10:04 pm I don’t know if this will help my friend. Good luck. I hate it when I have parts left over.![]()
3E9CB682-5A46-4B30-A30D-E09537A27285.jpeg
My issue is I wasn't the one to take it apart. But it's now mine once I go pick it up from the ffl next week
And thank you as always.
Last edited by cheezit on Thu Sep 12, 2019 10:23 pm, edited 1 time in total.
- 03Lightningrocks
- Senior Member
- Posts: 11460
- Joined: Tue Apr 08, 2008 5:15 pm
- Location: Plano
Re: Ruger new model single six part identification
It looks like part number 24 to me.
Last edited by 03Lightningrocks on Thu Sep 12, 2019 10:25 pm, edited 1 time in total.
NRA-Endowment Member
http://www.planoair.com
http://www.planoairconditioningandheating.com
http://www.planoair.com
http://www.planoairconditioningandheating.com
Re: Ruger new model single six part identification
This is my thought as well.03Lightningrocks wrote: Thu Sep 12, 2019 10:22 pm It looks like part number 24 to me. It holds the grip from slipping away from each other after they are tightened onto frame.
- 03Lightningrocks
- Senior Member
- Posts: 11460
- Joined: Tue Apr 08, 2008 5:15 pm
- Location: Plano
Re: Ruger new model single six part identification
I am not positive as to it's purpose but that is it for sure.cheezit wrote: Thu Sep 12, 2019 10:24 pmThis is my thought as well.03Lightningrocks wrote: Thu Sep 12, 2019 10:22 pm It looks like part number 24 to me. It holds the grip from slipping away from each other after they are tightened onto frame.
NRA-Endowment Member
http://www.planoair.com
http://www.planoairconditioningandheating.com
http://www.planoair.com
http://www.planoairconditioningandheating.com
Re: Ruger new model single six part identification
A grip pin stops them from rotating and maintains the correct location.03Lightningrocks wrote: Thu Sep 12, 2019 10:25 pmI am not positive as to it's purpose but that is it for sure.cheezit wrote: Thu Sep 12, 2019 10:24 pmThis is my thought as well.03Lightningrocks wrote: Thu Sep 12, 2019 10:22 pm It looks like part number 24 to me. It holds the grip from slipping away from each other after they are tightened onto frame.
I only hope it's that simple
-
txhighlander
- Senior Member
- Posts: 282
- Joined: Sun May 20, 2012 3:06 am
Re: Ruger new model single six part identification
On gunparts site , page 3 , part 24 hammer plunger pin is looking like the part. It gives a good picture.BHill wrote: Thu Sep 12, 2019 10:08 pm https://www.gunpartscorp.com/gun-manufa ... e-6?page=4
8 or 31
Cylinder latch spring plunger
Pawl spring plunger
Truth against the world
